withstand voltage isolation resistance i/p-o/p:3.75kvac i/p-fg:1.88kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh constant current region note.4 hln-80h-12 a b : ip64 rated. constant current level adjustable through output cable w ith 1~10vdc or 10v pwm signal or resistance. specification model dc voltage rated current rated power output voltage adj. range note.6 current adj. range line regulation load regulation setup, rise time note.8 hold up time (typ.) voltage range note.5 frequency range power factor (typ.) efficiency (typ.) ac current (typ.) input inrush current( .) typ leakage current safety standards note.7 working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over current note.4 over voltage over temperature can be adjusted by internal potentiometer or through output cable 16ms at full load 230vac /115vac 90 ~ 305vac 127 ~ 431vdc 47 ~ 63hz cold start 70a/230vac <0.75ma / 277vac 95 ~ 108% protection type : constant current limiting, recovers automatical ly after fault condition is removed compliance to en55015, en61000-3-2 class c ( 60% load, 12v model 65% loa d) ; en61000-3-3 compliance to en61000-4-2,3,4,5,6,8,11, en61547, en55024, lig ht industry level (surge 4kv), criteria a 20 ~ 95% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 40 ) 10 ~ 500hz, 2g 12min./1cycle, period for 72min. each along x, y, z axes 356.4khrs min. mil-hdbk-217f (25 ) 181*61.5*35mm (l*w*h) 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. constant current operation region is within 60% ~100% rated output vol tage. this is the suitable operation region for led related application s, but please reconfirm special electrical requirements for some specific syste m design. 5. derating may be needed under low input voltages. please check the static c haracteristics for more details. 6. type a only. 7. safety and emc design refer to en60598-1, cns15233, gb7000.1, fcc part 18. 8. length of set up time is measured at cold first start. turning on/off the powe r supply may lead to increase of the set up time. 9. the power supply is considered as a component that will be operated in combi nation with final equipment. since emc performance will be affected by th e complete installation, the final equipment manufacturers must re- qualify emc directive on the complete installation again. 0.5kg; 24pcs/13kg/0.75cuft protection type : shut down o/p voltage, re-power on to recover 80w single output switching power supply universal ac input / full range (up to 305vac)built-in active pfc function protections: short circuit / over current / over voltage / over temperature cooling by free air convection ocp point adjustable through output cable or internal potentiometer ip64 design for indoor or outdoor installations three in one dimming function (1~10vdc or pwm signal or resistance) suitable for led lighting and moving sign applications compliance to worldwide safety regulations for lighting 3 years warranty suitable for dry / damp location or outdoor application features : h l n - 8 0 h s e r i e s ripple & noise (max.) note.2 voltage tolerance note.3 environment safety & emc protection 100 10 (rth2) protection type : shut down o/p voltage, re-power on to recover selv ip64 a : ip64 rated. output voltage and constant current level can be adjusted th rough internal potentiometer. 14 ~ 17v 18 ~ 21v 23 ~ 27v 28 ~ 34v 34 ~ 38v 41 ~ 46v 54 ~ 60v 47 ~ 53v 59 ~ 65v 88% 89% 90% 90.5% 91% 91% 91% 91% 91% 2.5% 2.0% 1.0% 1.0% 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 2.0% 1.5% 1.0% 0.5% 0.5% 0.5% 0.5% 1.0% 0.5% 0.5% 1.0% 0.5% 0.5% 12v hln-80h-12 HLN-80H-30 hln-80h-15 hln-80h-36 hln-80h-20 hln-80h-42 hln-80h-24 hln-80h-48 hln-80h-54 15v 20v 24v 30v 36v 48v 5a 5a 4a 3.4a 2.7a 2.3a 1.7a 60w 75w 80w 81.6w 81w 82.8w 81.6w 150mvp-p 150mvp-p 13.5 ~ 17v 150mvp-p 17 ~ 22v 150mvp-p 22 ~ 27v 200mvp-p 27 ~ 33v 200mvp-p 33 ~ 40v 200mvp-p 43 ~ 53v 10.8 ~ 13.5v 54v 1.5a 81w 200mvp-p 49 ~ 58v 42v 1.95a 81.9w 200mvp-p 38 ~ 46v f m m 110 pf>0.96/115vac, pf>0.96/230vac, pf>0.94/277vac at full load (pl ease refer to "power factor characteristic" curve) 0.85a / 115vac 0.425a / 230vac 0.4a / 277vac en61347-1, en61347-2-13 independent , ip64 approved ; design refer t o ul60950-1, tuv en60950-1 , j61347-1, j61347-2-13 3 ~ 5a 3 ~ 5a 2.4 ~ 4a 2.04 ~ 3.4a 1.62 ~ 2.7a 1.38 ~ 2.3a 1.02 ~ 1.7a 0.9 ~ 1.5a 1.17 ~ 1.95a 7.2 ~12v 9 ~ 15v 12 ~ 20v 14.4 ~ 24v 18 ~ 30v 21.6 ~ 36v 28.8 ~ 48v 32.4 ~ 54v 25.2 ~ 42v 2000ms, 80ms / 115vac 000ms, 80ms / 230vac at full load ; b type 2000ms, 200ms at 95 % load 230vac / 115vac at full load 1 -40 ~ +50 (refer to "derating curve") emc immunity emc emission file name:hln-80h-spec 2011-07-28
mechanical specification case no.hln-80a unit:mm case no.hln-80b unit:mm fg (green/yellow) fg (green/yellow) 300 20 300 20 300 20 300 20 6.26 6.26 6.26 6.26 181 181 svt 18awg 2c ul2464 18awg 4c dim+ / dim- : commercial wall dimmer 1 ~ 10v & pwm control function 21.25 21.25 61.5 61.5 21.25 21.25 35 35 +v(red) -v(black) 2-r2.5 2-r2.5 svt 18awg 3c svt 18awg 3c ac/l(brown) ac/l(brown) ac/n(blue) ac/n(blue) ip64 rated. output voltage and constant current level can be adjusted thr ough internal (can access by removing the rubber stopper on the case). potentiometer. +v(red) dim+(blue) -v(black) dim-(white) 2.3 90.5 90.5 30.75 30.75 t case t case t case: max. case temperature. t case: max. case temperature. fosc : 100khz block diagram dim+ (b type) dim- detection pwm & pfc circuit o.l.p. o.t.p. emi filter rectifiers power switching filter & rectifiers +v -v i/p fg control o.v.p. & o.l.p. pfc circuit 80w single output switching power supply h l n - 8 0 h s e r i e s a type:(hln-80h-_a) b type:(hln-80h-_b) file name:hln-80h-spec 2011-07-28
64 68 72 76 80 84 88 92 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 277vac 230vac 115vac 0.78 0.80 0.82 0.84 0.86 0.88 0.90 0.92 0.94 0.96 0.98 1.00 50% 60% 70% 80% 90% 100% 277vac 230vac 115vac ambient temperature ( ) load (%) 230vac input only -40 -25 0 -10 15 30 40 50 60 20 40 60 80 100 (horizontal) hln-80h series possess superior working efficiency that up to 91% can be re ached in field applications. efficiency vs load (48v model) power factor characteristic load efficiency (%) pf load constant current mode (80w) 80w single output switching power supply h l n - 8 0 h s e r i e s file name:hln-80h-spec 2011-07-28 derating curve static characteristics input voltage (v) 60hz 90 100 125 135 145 155 165 175 180 200 230 305 100 90 80 70 60 50 40 load (%)
there are two major kinds of led drive method "direct drive" and "with led driv er". typical led power supply i-v curve a typical led power supply may either work in "constant voltage mode (cv) or c onstant current mode (cc)" to drive the leds. mean well's led power supply with cv+ cc characteristic can b e operated at both cv mode (with led driver, at area (a) and cc m ode (direct drive, at area (b). driving methods of led module vo(%) 100 60 50 95 (max.) io (%) constant voltage area constant current area hiccup protection (a) (b) (c) dimming operation(for b-type only) hln-80h b type please do not connect "dim-" to "-v". ip64 rated. output constant current level can be adjusted through outpu t cable by connecting a resistance or built-in 3 in 1 dimming function, vo and io can not be adjusted (b type) 1 ~ 10vdc or 10v pwm signal between dim+ and dim-. reference resistance value for output current adjustment (typical ) 1 ~ 10v dimming function for output current adjustment (typical) 10v pwm signal for output current adjustment (typical): frequency ra nge:100hz ~ 3khz fg (green/yellow) ac/l(brown) ac/n(blue) +v(red) dim+(blue) -v(black) dim-(white) 80w single output switching power supply h l n - 8 0 h s e r i e s file name:hln-80h-spec 2011-07-28 60% 1v 4v 7v 2v 5v 8v 3v 6v 9v 10v 10% 20% 30% 40% 50% 70% 80% open open 90% 100% dimming value percentage of rated current 60% 60% 10% 10% 20% 20% 30% 30% 40% 40% 50% 50% 70% 70% 80% 80% 90% 90% 100% 100% duty value percentage of rated current 102%~108% 102%~108% 60k 60% 10k 10k /n 20k /n 30k /n 40k /n 50k /n 60k /n 70k /n 80k /n 90k /n 100k /n single driver multiple drivers (n=driver quantity for synchronized dimming operation) 10% 20k 20% 30k 30% 40k 40% 50k 50% 70k 70% 80k 80% 90k 100k open 90% 100% resistance value percentage of rated current 102%~108% -----
dimming connection diagram for turning the lighting fixture on/off : using a switch and relay can turn on/off the lighting fixture. using the built-in dimming function on b-type model can't turn the lighti ng fixture totally dark. please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the led power s upply unit. 1.output constant current level can be adjusted through output cable by c onnecting a or 1~10vdc or 10v pwm signal between dim+ and dim-. resistance 2.the led lighting fixture can be turned on/off by the switch. n fg l relay blue brown green/ yellow ac/l ac/n hln-80h b type dim+ dim- v(-) v(+) blue white black red switch adjuster 0~100k ohms resistance 1~10v dc voltage 10v pwm signal led lighting fixture 80w single output switching power supply h l n - 8 0 h s e r i e s file name:hln-80h-spec 2011-07-28
|
